128×64 Graphic OLED Display

Model No. WEO012864AC

128×64 OLED Display, OLED Display 128×64
Type: Graphic
Structure: COG
Size: 0.96″
IC：SSD1315
3V power supply
1/64 duty
Interface: 6800, 8080, SPI, I2C
Display Color: White / Yellow

PDF DOWNLOAD
DEMO CODE
ADD TO INQUIRY

Categories: Graphic OLED Display, OLED Module

Description

WEO012864AB module supports internal Charge Pump supply and external VCC supply.

Drawing

128x64 OLED Display, 128x64 OLED LCD, OLED Module 128x64, OLED Display 128 x 64 - WEO012864AC
Data source ref: WEO012864ACWPP3N00000

SPECIFICATIONS

Interface Pin Function

No.

Symbol

Function

N.C. (GND)

The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

C2N

C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.

C2P

C1P

C1N

VBAT

This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.

VSS

Ground pin. It must be connected to external ground.

VDD

Power supply pin for core logic operation.

BS0

These pins are MCU interface selection input. See the
following table:

	BS0	BS1	BS2
I2C	0	1	0
3-wire SPI	1	0	0
4-wire SPI	0	0	0
8-bit 68XX Parallel	0	0	1
8-bit 80XX Parallel	0	1	1

BS1

BS2

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.

D/C#

This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.

R/W#

This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

18~25

D0~D7

These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

IREF

When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.

VCOMH

The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.

VLSS

This is an analog ground pin. It should be connected to VSS externally.

NC
(GND)

The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

General Specification

Item	Dimension	Unit
Dot Matrix	128 x 64	－
Module dimension	26.70 × 19.26 ×1.26	mm
Active Area	21.74 × 10.86	mm
Pixel Size	0.15 × 0.15	mm
Pixel Pitch	0.17 × 0.17	mm
Display Mode	Passive Matrix
Display Color	Monochrome
Drive Duty	1/64 Duty
Controller IC	SSD1315
Interface	6800, 8080, SPI, I2C
Size	0.96 inch

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Supply Voltage for Logic	VDD	0	4.0	V
Charge Pump Regulator Supply Voltage	VBAT	0	6.0	V
Supply Voltage for Display	VCC	0	15.0	V
Operating Temperature	TOP	-40	+80	°C
Storage Temperature	TSTG	-40	+85	°C

Electronical Characteristics

DC Electrical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Charge Pump Regulator Supply Voltage	VBAT	－	2.4	3.5	5.0	V
Supply Voltage for Display	VCC	－	6.0	12.0	12.5	V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC)	Charge Pump VPP	－	7.0	7.5	－	V
Input High Volt.	VIH	－	0.8xVDD	－	VDD	V
Input Low Volt.	VIL	－	0	－	0.2xVDD	V
Output High Volt.	VOH	－	0.9xVDD	－	VDD	V
Output Low Volt.	VOL	－	0	－	0.1xVDD	V
Operating Current for VCC (50% display ON) (VCC Supplied Externally)	ICC	VCC=12V	－	10	20	mA
50% checkerboard operating Current (VCC Generated by Internal DC/DC)	IBAT	－	－	15	30	mA

Search keyword: 128×64 oled, oled 128×64, oled display 128×64, 0.96 oled, 0.96″ oled, 0.96 inch oled, oled 0.96, oled 0.96″