2.7″, 128×64 Graphic OLED Display with Capacitive Touch Panel

Model No. WEO012864Q-CTP

Type: Graphic (Without Frame)
Structure: COG
Size: 2.7 inch
128 x 64 Dot Matrix
IC：SSD1309
3V Power supply
1/64 duty
Interface: 6800, 8080, SPI, I2C
With Capacitive Touch Screen (CTP)
Detect Point : 1 Finger
Display Color: White / Yellow / Sky Blue / Green

Categories: OLED Module, OLED Touch Display

Description

WEO012864Q-CTP is the most popular 2.7 inch COG Graphic OLED display with Capacitive Touch Panel on module; which is made of resolution 128×64 dots. This module is built in with SSD1309 IC, it supports 6800/8080 8-bit parallel, 4-Wire SPI and I2C interface, supply voltage for logic is from 2.8V to 3.3V, typical value 3.0V, supply voltage for display 13V, 1/64 driving duty. This WEO012864Q-CTP model adopted GT911 as touch IC, which supports I2C interface, one Detect Point for CTP.

This 2.7″ WEO012864Q with CTP model is ideal for smart home applications, intelligent technology devices, energy systems, meter devices, communication systems, medical instrument, etc. This module can be operating at temperatures from -20℃ to 70℃; its storage temperatures range from -30℃ to 80℃. Sporting a high contrast ratio of 10,000:1 and an expansive viewing angle of up to 160°, this OLED module ensures clearer display images.

Drawing

2.7, 128x64 Graphic OLED Display with Capacitive Touch Panel - WEO012864Q-CTP

Data source ref: WEO012864QWPP3D00F00

SPECIFICATIONS

Interface Pin Function

No.

Symbol

Function

NC(GND)

No connection

VLSS

This is an analog ground pin

VSS

Ground.

No connection

VDD

Power supply pin for core logic operation

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select

	BS1	BS2
I2C	1	0
4-wire Serial	0	0
8-bit 68XX parallel	0	1
8-bit 80XX parallel	1	1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

BS2

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

D/C#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.

R/W#

This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

13-20

D0~D7

These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

IREF

This pin is the segment output current reference pin.
IREF is supplied externally.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.

NC(GND)

No connection

CTP PIN Definition

No.	Symbol	Function
1	GND	Power ground
2	VDD	Power supply
3	INT	Interrupt signal, active low, asserted to request Host start a new transaction
4	SDA	I2C data signal
5	SCL	I2C clock signal
6	RST	External reset signal, active low
7	GND	Power ground
8	GND	Power ground
9	GND	Power ground
10	GND	Power ground

Mechanical Data

Item	Dimension	Unit
Dot Matrix	128 x 64	－
Module dimension	74.8 × 44.16 × 3.66	mm
Active Area	61.41 × 30.69	mm
Pixel Size	0.45 × 0.45	mm
Pixel Pitch	0.48 × 0.48	mm
Display Mode	Passive Matrix
Display Color	Monochrome
Drive Duty	1/64 Duty
IC	SSD1309
Interface	6800,8080,4-Wire SPI,I2C
Size	2.7 inch
CTP IC	GT911
Detect Point	1
CTP Interface	I2C
Surface	Glare

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Supply Voltage for Logic	VDD	-0.3	4	V
Supply Voltage for Display	VCC	0	15	V
Operating Temperature	TOP	-20	+70	°C
Storage Temperature	TSTG	-30	+80	°C

Touch Panel Controller GT911

Parameter	Symbol	Min	Max	Unit
Power Supply Voltage	VDD	2.66	3.47	V

Electronical Characteristics

DC Electrical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage for Logic	VDD	－	2.8	3.0	3.3	V
Supply Voltage for Display	VCC	－	12.5	13	13.5	V
High Level Input	VIH	－	0.8×VDD	－	－	V
Low Level Input	VIL	－	－	－	0.2×VDD	V
High Level Output	VOH	－	0.9×VDD	－	－	V
Low Level Output	VOL	－	－	－	0.1×VDD	V
50% Check Board operating Current		VCC =13.0V	－	30	50	mA

Touch Panel Controller GT911

Item	Symbol	Min	Typ	Max	Unit
Supply Voltage	VDD	2.8	3.0	3.3	V
Input High Volt.	VIH	0.75xVDD		VDD+0.3	V
Input Low Volt.	VIL	-0.3	－	0.25xVDD	V
Output High Volt.	VOH	0.85xVDD	－	－	V
Output Low Volt.	VOL	－	－	0.15xVDD	V

Search keyword: 128×64 oled, oled 128×64, 2.7 oled, 2.7 inch oled, oled 2.7